ELECDURA NETWORK
Your Whole New Supply Chain For Heavy-Duty Parts
Whatsapp：
+86 18915027366
Phone：
+86 18915027366
Toyota 3L 36mm Configuration
Elecdura
Available for qualified orders
20 pcs
7 - 15 Days
Neutral packaging / private-label review
18 Months
Toyota 3L; 12V, 2.0kW, 10T, 36mm pinion reference
Confirm 10T pinion and 36mm reference, mounting face, drive reach, solenoid position and terminal orientation, 12V, 2.0kW, solenoid position and terminal layout against the removed starter before volume supply.
| Quantity: | |
|---|---|
Distributors supporting Toyota 3L can source Toyota 3L 36mm Configuration in the ND-type replacement configuration. The stated 12V, 2.0kW rating and 10T pinion are kept visible because this product keeps the stated 12V 2.0kW configuration attached to Toyota 3L when purchasing teams compare old-unit photographs; they should remain on the purchase order and receiving record.
Equipment dealer teams handling engine-overhaul planning should send Toyota 3L 36mm Configuration, the Toyota 3L record, required quantity, destination and delivery timing together. Add straight drive-end and terminal-side photographs of the removed starter. Elecdura can then address cleaner branch replenishment, mixed-SKU export packing and the correct physical configuration in one useful commercial offer.
| Primary order identity | Toyota 3L 36mm Configuration |
| Target application | Toyota 3L |
| Starter design | ND-type replacement |
| System voltage | 12V |
| Rated output | 2.0kW |
| Pinion identification | 10T / 36mm reference |
| OE / reference group | Application and physical unit details |
| Wholesale terms | MOQ 20 pcs / normally 7–15 days after order confirmation |
| Warranty | 18 months under agreed sales terms |
Receiving and technical teams should concentrate on 10T pinion and 36mm reference, mounting face, drive reach, solenoid position and terminal orientation. A square drive-end image plus a side image gives a much clearer comparison of mounting, locating and pinion relationships than a general product shot, reducing the chance of releasing a visually similar but unsuitable unit.
The 2.0kW output and 10T drive belong together with 12V. Record all three rather than quoting power alone, and include a terminal-side photograph so the B+ cable, control wire and nearby clearances can be reviewed before shipment.
For repeat supply, store Toyota 3L 36mm Configuration, Toyota 3L, the received lot and the confirmed old-unit photographs together. That record allows a distributor to reorder the same configuration without rebuilding the decision from a loose list of aftermarket numbers.
For engine-overhaul planning, keep Toyota 3L 36mm Configuration, Toyota 3L, 12V, 2.0kW and 10T on one purchasing record. At goods-in, review drive-end geometry before releasing the lot. This gives the equipment dealer a documented basis for cleaner branch replenishment when the next order is raised.
Wholesale buyers may combine an initial verification order with a forward replenishment plan, provided each reference remains clearly separated. Normal terms are MOQ 20 pieces, 7–15 days after confirmation and an 18-month warranty; packing and freight are quoted for the stated destination.
Demand from an engine-overhaul workshop should keep Toyota 3L 36mm Configuration tied to Toyota 3L. For engine-overhaul planning, the equipment dealer can use a central-to-branch transfer plan, archive the carton and lot label and review drive-end geometry at goods-in. This supports cleaner branch replenishment while keeping mixed-SKU export packing visible.
The video below introduces Elecdura starter-motor production and electrical testing for B2B supply. Buyers can review factory capability while using the Toyota 3L 36mm Configuration application and specification shown above for their own product comparison.
Equipment dealer teams should tie Toyota 3L 36mm Configuration to Toyota 3L, 12V, 2.0kW, 10T and the removed-unit photographs before requesting price. For engine-overhaul planning, state quantity, destination and delivery timing, then review drive-end geometry. Ask Elecdura to address mixed-SKU export packing and cleaner branch replenishment in the same quotation.
No. Tooth count is only one control. The locating face, mounting pattern, pinion reach, 36mm reference, solenoid position, terminals and 12V system must also agree with the removed starter. Review the full set before a sample or bulk order is accepted. Retain the Toyota 3L 36mm Configuration result for engine-overhaul planning.
A sample is useful when the old label is incomplete, the application record is uncertain or several similar housings are in local stock. Confirm the sample against mounting, drive and electrical details before scaling the order. Keep the accepted photographs and measurements for later purchasing and receiving checks. File Toyota 3L 36mm Configuration with the drive-end geometry check.
Send the complete Toyota 3L 36mm Configuration reference, Toyota 3L details, quantity, destination and required date. Add clear front, side and terminal photographs of the removed starter. This gives Elecdura enough information to discuss the intended 12V 2.0kW 10T unit, packing, lead time and freight in one focused offer. Use Toyota 3L 36mm Configuration when arranging mixed-SKU export packing.
Tell Elecdura the quantity, destination, required arrival date and whether the demand supports an urgent repair, normal replenishment or a planned project. Normal preparation is 7–15 days after confirmation, but freight and packing choices depend on the actual schedule and shipment size. This supports cleaner branch replenishment for Toyota 3L 36mm Configuration.
Use the full reference, Toyota 3L application and core specification on the internal item label. Store the confirmed product photographs with the ERP record and avoid abbreviating the number. Receiving staff can then compare each new lot with the same documented configuration before distributing it to branches. Keep Toyota 3L 36mm Configuration traceable through engine-overhaul planning.
Provide the invoice or lot reference, installation date, Toyota 3L details, service time and a clear description of the symptom. Include photographs of the flange, drive and terminals plus battery and voltage-drop results. Keep the unit assembled until Elecdura confirms the next step under the agreed terms. Link Toyota 3L 36mm Configuration photographs to the drive-end geometry record.
Confirm carton count, labels and visible condition before sampling. On selected units, compare the pinion, mounting face, solenoid and terminals with the confirmed record. Isolate any damaged or different unit with carton and lot photographs before the remainder is released to normal Toyota 3L inventory. Carry the Toyota 3L 36mm Configuration result into mixed-SKU export packing.
Email info@elecdurauto.com with Toyota 3L 36mm Configuration, Toyota 3L details, old-unit photographs, quantity, delivery country and required date. Elecdura will reply with the matching 12V 2.0kW 10T offer, availability, packing, lead time and freight options.
