ELECDURA NETWORK
Your Whole New Supply Chain For Heavy-Duty Parts
 E-mail :
 Whatsapp:
  +86 18915027366
 Phone:
  +86 18915027366
You are here: Home » Blog » Heavy Duty Alternators » Can a Delco Remy 8600307 Replace an 8600313 on Your Truck?

Can a Delco Remy 8600307 Replace an 8600313 on Your Truck?

Views: 0     Author: Site Editor     Publish Time: 2026-11-17      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Both are 12 V, 200 A Delco Remy 28SI alternators. If your truck has a fixed J180 bracket sized for Delco Remy 8600313, ask for the short-hinge alternator. The mounting holes on 8600307 are 18 mm farther apart. If the truck has an adjustable J180 slide bracket, the long-hinge unit is a candidate. Before you approve it, check the bracket on that truck and confirm the pulley and electrical connections on the part the supplier will ship.

Why both numbers appear on the same quote

ASC Auto Electric lists 8600307 as “Can Use” on its 8600313 catalog page. That entry explains why a parts desk might offer the other number. The catalog can identify a candidate, but only the mounting arrangement on your equipment can settle the 18 mm question.

ASC cross-reference

Delco Remy part

Electrical rating

Mount

Front hole spacing

8600313

12 V · 200 A

J180 short hinge

198 mm / 7.79 in

8600307

12 V · 200 A

J180 long hinge

216 mm / 8.50 in

8600314

12 V · 200 A

Pad mount

Different bolt pattern

All three are 12 V, 200 A members of the 28SI family. Both hinge versions carry the Delco Remy name, so the brand on the tag cannot tell you which one you have. If the unit bolts down on mounting pads, use the pad-mount drawing. The two hinge dimensions in the table apply only to the upper and lower holes on the pulley end of a hinge-mount unit.

28SI mounting drawings, p. 10 · 28SI model list, p. 2

How to measure a 28SI with the tag missing

Find the two holes on the pulley end

Set the removed alternator on a stable work surface, pulley facing you, with one mounting ear above the other. Locate the bolt hole in each ear and measure between the two centers. Measuring from a front ear to a rear ear gives the axial spacing, along the shaft. For this check, use the two holes on the front face. Leave the shaft and housing screws out of the measurement.

Read the ruler when the pulley is in the way

If the pulley blocks the ruler, move it to one side. As you move it, keep its edge parallel to the line between the hole centers and its marked face in the same plane as the hole openings. Look straight at the face. Align zero directly across from the upper center and read the mark directly across from the lower center. Both sight lines should meet the ruler at right angles. Photograph both holes and the scale in one shot.

Record the actual reading. If you get, say, 207 mm, keep that number and recheck your setup. The drawing gives nominal sizes. A worn oval hole or a tilted ruler can spoil the reading. If the measurement is still ambiguous or conflicts with the tag, send the photo and any legible part number to the supplier. Ask for a dimensioned drawing before choosing a hinge style.

28SI mounting drawings, p. 10

Will the other hinge fit your bracket?

Fixed J180 bracket

With a fixed bracket, the replacement must match the mounting-hole spacing required by that bracket. If the bracket takes a 198 mm short-hinge unit and the supplier’s drawing shows 216 mm, request a corrected quote for the short hinge.

Adjustable J180 slide bracket

Delco Remy says an adjustable J180 slide bracket can accommodate either hinge length. The arm allows movement for belt tension adjustment. Take one photo showing both mounting points and a close-up of the full slot and bolt position. A shot of one bolt alone leaves the supplier guessing about the other end of the bracket.

Delco Remy mounting guide

A ForeForums contributor discussing these two part numbers said the upper brace on that particular coach could pivot to fit either unit. You can answer the same question for your truck by showing how the upper brace attaches. A photo of the loose alternator misses that detail.

ForeForums, reply 17

What else to verify before approving the quote

Pulley and belt alignment

Ask whether the quoted alternator comes with a pulley or requires you to reuse the old one. For a supplied pulley, compare the belt profile, groove count where applicable, diameter and offset with your original. Ask for the groove position relative to the same mounting face on both drawings. A front view can show the grooves, but a side view or dimensioned drawing is needed to judge where the belt will run.

Terminals on the exact part being shipped

Delco Remy lists the same electrical details for new units 8600313 and 8600307. Both have negative ground, a 5/16-inch B+ output stud, No. 10 R and I terminals, and a Remote Sense terminal. Ask for a rear-view photo of the offered unit with the terminal labels visible. Compare it with the terminals your truck actually uses.

8600313 specifications · 8600307 specifications and alternatives

Delco Remy also lists 8700083, a remanufactured 12 V, 200 A long-hinge unit, among the replacement options for 8600307. Its listing shows no Remote Sense terminal. If the truck uses Remote Sense, verify that the specific replacement unit includes that terminal before accepting the offer.

8600307 specifications and alternatives

What to send the supplier

Send the old part number or a nameplate photo, the truck or engine model, the quantity, the ruler photo and the bracket photos. Include the pulley and rear terminals if you are considering the other hinge style. If you stock both configurations, put each on its own purchase-order line with its hinge style and nominal spacing. That gives receiving staff something they can check against the part in the box.

Example reply to a long-hinge quote

We requested a replacement for Delco Remy 8600313. Your quote lists 8600307. Our old unit measures 198 mm between the front mounting-hole centers, and our bracket is fixed. Please quote the short-hinge unit and send the drawing for the part you’ll ship. Please also confirm whether the pulley is included and send a photo of the rear terminals.

If you have an adjustable slide bracket, change the request to: “We’ve attached photos of both mounting points and the full slot. Can you confirm the 216 mm long-hinge unit fits this application, including pulley alignment and the terminals shown?” Keep the supplier’s written confirmation with the quote.

Request a heavy-duty alternator quote

Contact us

Tell Us About Your Sourcing Needs

Share your product requirements, target market, and estimated order plan. Our team will help match suitable products and provide a fast quotation for your wholesale program.
Contact us
Heavy-Duty Parts. 
On Time. On Demand.
One-Stop Supplier in China
System
About
Contact Info
+86-189-1502-7366
A2 Block, Shimao Plaza, Changzhou, China
COPYRIGHT © 2025 ELECDURAUTO ALL RIGHTS RESERVED.