STA1422 Chevrolet Starter Motor 12V 0.80kW 8T

STA1422 Chevrolet Starter Motor Replacement Supply for B2B Procurement

STA1422 is intended for procurement against Chevrolet equipment identified by starter reference STA1422 with a 12V, 0.80kW, 8-tooth clockwise configuration. Keep the approved unit photos, application record and full reference group together so future quotations and repeat orders stay linked to the same physical starter.

The distributor record for STA1422 should connect the reference group STA1422 / 101422 / LRS02246 / 6046103 / 96469962 / 33246N with Chevrolet equipment identified by starter reference STA1422. Add the old-unit label, mounting-face image, terminal view and receiving result to that record. Reuse it for repeat quotations, but create a new revision whenever the supplier changes the suffix, housing, pinion or electrical rating. A disciplined record reduces avoidable substitutions during urgent replenishment.

STA1422 Starter Motor B2B Production and Test Video for B2B Supply

This video introduces Elecdura starter-motor production and supply capabilities. Use the product-specific specification, reference and fitment evidence on this page as the purchasing control for STA1422.

STA1422 Starter Motor Distributor Specifications for Aftermarket Buyers

STA1422 Starter Motor OE Cross-Reference Review for Fleet Replacement

Use STA1422 as the primary purchasing reference and cross-check 101422, LRS02246, 6046103, 96469962, 33246N. These numbers identify the candidate starter family, but approval still requires the exact suffix, electrical rating, drive end, mounting geometry, pinion and terminal layout to match the removed unit or signed sample.

STA1422 Starter Motor Bulk Fitment Approval for Wholesale Supply

Confirm the complete STA1422 / 101422 / LRS02246 / 6046103 / 96469962 / 33246N group together with the 12V, 0.80kW, 8-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

STA1422 Starter Motor Wholesale Receiving Inspection for Distributor Sourcing

For a wholesale shipment, sample units across the STA1422 lot rather than inspecting only the top carton. Compare reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability with the approval record and document pass, fail and hold quantities. Do not mix a disputed suffix or drive-end version with cleared stock, even when the outer housing looks alike.

STA1422 Starter Motor MOQ and Private-Label Supply for Bulk Procurement

STA1422 Starter Motor Distributor FAQ for B2B Supply

Where is STA1422 commonly used, and what still needs confirmation?

Confirm the complete STA1422 / 101422 / LRS02246 / 6046103 / 96469962 / 33246N group together with the 12V, 0.80kW, 8-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

What specification mismatch creates the greatest risk on STA1422?

Confirm the complete STA1422 / 101422 / LRS02246 / 6046103 / 96469962 / 33246N group together with the 12V, 0.80kW, 8-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

Which configuration checks prevent a mismatched STA1422 order?

Confirm the complete STA1422 / 101422 / LRS02246 / 6046103 / 96469962 / 33246N group together with the 12V, 0.80kW, 8-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

Which mounting details should be compared before ordering STA1422?

Measure and compare the equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement with the removed starter. Check bolt-hole spacing, locating diameter, starter clocking, pinion rest position and rear-terminal clearance instead of judging from the outer housing alone. Never pull a misaligned unit into place with mounting bolts. A measured or photographed fitment record is especially valuable when nearby references share the same voltage and tooth count but use another drive-end or solenoid orientation.

Which incoming-inspection points matter for STA1422?

Tie every carton and sampled unit to STA1422, the approved reference document and the supplier lot. Inspect reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability, then compare the sampled unit with the signed photos or dimensional document. Record pass and fail quantities before the stock is mixed. Quarantine any different rating, pinion, mounting face or terminal layout, because an unverified substitute can stop equipment, generate a claim and turn a low unit price into a costly order. This receiving discipline is cheaper than sorting returns after distribution.

Can a similar 12V starter replace STA1422?

A substitute is acceptable only when its complete reference relationship, 12V system, 0.80kW rating, 8T, rotation and mounting geometry agree with the approved unit. Similar appearance or a shared partial number is not enough. Ask for application and old-unit evidence, then test or approve a sample before changing the order line. Keep materially different versions separate in inventory so warehouse staff cannot fulfil one inquiry with the wrong variant.

How can buyers separate a STA1422 fault from an equipment fault?

Check battery capacity, voltage drop, start signal, grounds, ring gear and mechanical engine load before condemning the starter. Record battery voltage at rest and during the start command, then measure voltage drop under load; a weak supply or poor ground can imitate starter failure. Inspect the mounting surface and gear engagement as well. Attach these results, the old-unit label and failure symptoms to the claim so the supplier can distinguish a product defect from an upstream electrical or mechanical problem.

What makes a STA1422 RFQ technically complete?

Send STA1422 and all visible OE or catalog references, the full application or engine record, required quantity, destination and target delivery date. Add clear photos of the label, drive end, mounting face and terminals, plus any dimensional drawing available. State packaging, private-label, sample and inspection requirements at the start. A technically complete RFQ lets the supplier quote one verified configuration and reduces clarification delays after price approval.

How are MOQ, samples and repeat orders managed for STA1422?

The standard MOQ is 20 pieces, subject to final order confirmation, and a sample or pre-production approval should precede volume release when fitment information is incomplete. Mark the approved sample with STA1422, buyer application and revision date. Repeat orders should reference that same approval plus any packaging specification. If the supplier, suffix or physical design changes, treat it as a new approval rather than assuming the previous decision still applies.

Request a B2B Quote for STA1422 Starter Motors

Send the complete reference, Chevrolet equipment identified by starter reference STA1422, old-unit photos, quantity, destination and packaging or inspection requirements. Elecdura will use that evidence to review one defined aftermarket starter configuration for your quotation.