00010DB58E Heavy-Duty Starter Motor 12V 2.0kW 9T

00010DB58E Heavy-Duty Starter Motor Distributor Supply and Fitment Control

For repeat wholesale supply, 00010DB58E should remain tied to equipment identified by starter reference 00010DB58E and the exact 12V, 2.0kW, 9-tooth clockwise configuration. Record the accepted old-unit label and physical sample so purchasing, receiving and warranty teams do not mix an adjacent starter variant with the approved item.

A reliable B2B listing for 00010DB58E is more than a cross-reference lookup. The sourcing file should show how 00010DB58E / 0001109064 / 0001109065 / 0986021610 / 1986S00725, equipment identified by starter reference 00010DB58E, the old unit and the supplied sample were reconciled. Keep photographs and inspection results with the buyer's internal item code, then require a fresh approval if any electrical or mechanical characteristic changes on a later production lot.

00010DB58E Starter Motor B2B Production and Test Video for B2B Supply

This video introduces Elecdura starter-motor production and supply capabilities. Use the product-specific specification, reference and fitment evidence on this page as the purchasing control for 00010DB58E.

00010DB58E Starter Motor Distributor Specifications for Aftermarket Buyers

00010DB58E Starter Motor OE Cross-Reference Review for Fleet Replacement

Use 00010DB58E as the primary purchasing reference and cross-check 0001109064, 0001109065, 0986021610, 1986S00725. These numbers identify the candidate starter family, but approval still requires the exact suffix, electrical rating, drive end, mounting geometry, pinion and terminal layout to match the removed unit or signed sample.

00010DB58E Starter Motor Bulk Fitment Approval for Wholesale Supply

Fitment control for 00010DB58E starts with the old starter and the application record. Compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement, and do not force a unit into position with the mounting bolts. If the reference family includes multiple ratings or tooth counts, create separate approval and inventory records for each physical version.

00010DB58E Starter Motor Wholesale Receiving Inspection for Distributor Sourcing

Inspect incoming 00010DB58E lots against the signed sample and purchase-line specification. Check reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability, record the result by lot and quarantine any mixed version before it reaches saleable inventory. This prevents a low-cost receiving shortcut from becoming an unverified substitute that can stop equipment, generate a claim and turn a low unit price into a costly order.

00010DB58E Starter Motor MOQ and Private-Label Supply for Bulk Procurement

00010DB58E Starter Motor Distributor FAQ for B2B Supply

What engine or equipment data is required for 00010DB58E?

Confirm the complete 00010DB58E / 0001109064 / 0001109065 / 0986021610 / 1986S00725 group together with the 12V, 2.0kW, 9-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

Why must 12V, 2.0kW and 9T be checked together on 00010DB58E?

Confirm the complete 00010DB58E / 0001109064 / 0001109065 / 0986021610 / 1986S00725 group together with the 12V, 2.0kW, 9-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

What must be approved before volume supply for 00010DB58E?

Confirm the complete 00010DB58E / 0001109064 / 0001109065 / 0986021610 / 1986S00725 group together with the 12V, 2.0kW, 9-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

How can a buyer prevent a bolt-up mismatch on 00010DB58E?

Measure and compare the equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement with the removed starter. Check bolt-hole spacing, locating diameter, starter clocking, pinion rest position and rear-terminal clearance instead of judging from the outer housing alone. Never pull a misaligned unit into place with mounting bolts. A measured or photographed fitment record is especially valuable when nearby references share the same voltage and tooth count but use another drive-end or solenoid orientation.

How should a wholesale shipment of 00010DB58E starters be inspected?

Tie every carton and sampled unit to 00010DB58E, the approved reference document and the supplier lot. Inspect reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability, then compare the sampled unit with the signed photos or dimensional document. Record pass and fail quantities before the stock is mixed. Quarantine any different rating, pinion, mounting face or terminal layout, because an unverified substitute can stop equipment, generate a claim and turn a low unit price into a costly order. This receiving discipline is cheaper than sorting returns after distribution.

When is a cross-referenced substitute acceptable for 00010DB58E?

A substitute is acceptable only when its complete reference relationship, 12V system, 2.0kW rating, 9T, rotation and mounting geometry agree with the approved unit. Similar appearance or a shared partial number is not enough. Ask for application and old-unit evidence, then test or approve a sample before changing the order line. Keep materially different versions separate in inventory so warehouse staff cannot fulfil one inquiry with the wrong variant.

Which system checks should precede a 00010DB58E warranty claim?

Check battery capacity, voltage drop, start signal, grounds, ring gear and mechanical engine load before condemning the starter. Record battery voltage at rest and during the start command, then measure voltage drop under load; a weak supply or poor ground can imitate starter failure. Inspect the mounting surface and gear engagement as well. Attach these results, the old-unit label and failure symptoms to the claim so the supplier can distinguish a product defect from an upstream electrical or mechanical problem.

What information is needed for a 00010DB58E wholesale quotation?

Send 00010DB58E and all visible OE or catalog references, the full application or engine record, required quantity, destination and target delivery date. Add clear photos of the label, drive end, mounting face and terminals, plus any dimensional drawing available. State packaging, private-label, sample and inspection requirements at the start. A technically complete RFQ lets the supplier quote one verified configuration and reduces clarification delays after price approval.

Can 00010DB58E be sampled before a distributor order?

The standard MOQ is 20 pieces, subject to final order confirmation, and a sample or pre-production approval should precede volume release when fitment information is incomplete. Mark the approved sample with 00010DB58E, buyer application and revision date. Repeat orders should reference that same approval plus any packaging specification. If the supplier, suffix or physical design changes, treat it as a new approval rather than assuming the previous decision still applies.

Request a B2B Quote for 00010DB58E Starter Motors

Send the complete reference, equipment identified by starter reference 00010DB58E, old-unit photos, quantity, destination and packaging or inspection requirements. Elecdura will use that evidence to review one defined aftermarket starter configuration for your quotation.