428000-6030 CASE Starter Motor 12V 2.7kW 10T

428000-6030 Construction Equipment Starter Motor for CASE SR250 skid steer loader

For private-label buyers defining label requirements, 428000-6030 supports excavator, loader and off-highway replacement programs for CASE SR250 skid steer loader. This construction equipment starter motor is defined by its 12V electrical system, 2.7kW output and 10T pinion, giving distributors a practical basis for quotation and stock matching.

For purchasing teams confirming commercial terms, distributors can quote the exact application and starter configuration without turning the page into a generic component guide. Elecdura can also review customer labels, carton requirements and inspection documents for planned orders.

428000-6030 Starter Motor Specifications and Technical Drawing

For fitment reviewers confirming the stated application, because no dimensional drawing is available for this version, the approved product views, full reference and 12V 2.7kW 10T specification should be compared with the starter being replaced. Customer measurements can then complete the fitment review without introducing unverified dimensions.

For application specialists checking application evidence, A dimensional drawing was not supplied for 428000-6030. For a fitment enquiry, provide straight-on images of the mounting face and drive end plus the locating diameter, hole spacing, pinion projection and terminal direction measured from the starter being replaced.

428000-6030 Aftermarket Replacement and Application

For distributors reviewing a replacement proposal, the replacement search starts with 428000-6030 and the CASE SR250 skid steer loader application. For mixed fleets or previously repaired machines, add clear old-unit photos so a substituted starter does not become the only fitment evidence.

For technical buyers preparing a technical RFQ, A direct replacement decision should combine the OE group with physical comparison. Check the mounting face, 10T drive and cable-stud direction, and ask for a separate review when one of those features differs.

428000-6030 Wholesale Supply for Distributors and Importers

For engine-parts specialists preparing a volume quote, buyers can discuss 20 pcs MOQ, production planning around 7–15 days after confirmation, neutral cartons or private-label packaging, and an 18-month warranty under the agreed sales terms.

For regional parts suppliers planning a repeat order, batch consistency should be controlled through the agreed reference, electrical rating, pinion, packaging and inspection points. Elecdura can discuss test documentation and pre-shipment photos that match the needs of the distributor or importer.

428000-6030 Starter Motor Buyer FAQ

How can an importer validate 428000-6030 side-profile photograph for a first commercial order?

For product managers preparing a technical RFQ, the side profile of 428000-6030 shows body length, solenoid placement and the relationship between flange and drive. Compare it with a square side view of the removed starter, then use measured axial references where available. This angle helps reveal a housing or projection difference that a front-only photograph can miss.

What evidence best identifies 2.7kW output on CASE SR250 skid steer loader before an installation slot is booked?

For maintenance suppliers checking version-defining data, the 2.7kW rating belongs to the 428000-6030 configuration used for CASE SR250 skid steer loader. Verify the old-unit rating and investigate battery voltage, cable drop and engine turning resistance before choosing another output. A higher or lower kW figure is not an automatic upgrade; it can indicate a separate starter design with different electrical and mechanical requirements.

Which comparison prevents a mismatch for 12V system compatibility for repeatable sourcing?

For equipment-parts dealers confirming electrical ratings, 428000-6030 is a 12V starter and must be connected only to the matching machine electrical system. Read the voltage marking on the old unit and verify the battery arrangement ahead of the order. A housing can look correct while the winding and solenoid are designed for another voltage, so appearance must not override the electrical label.

How should a workshop distinguish 428000-6030 ring-gear engagement for a documented fitment decision?

For purchasing teams checking repeat-order specifications, review the 10T pinion, module 3.175, rest position and available axial dimensions as one engagement set. Inspect the ring gear for wear before fitting. A correct bolt pattern cannot protect the gear if pitch or projection differs, so drive geometry should be resolved before the starter is energized.

What should receiving teams compare on module 3.175 when the unit taken from service is available?

For distributors matching the old starter, module 3.175 is part of the gear geometry for 428000-6030. Confirm it together with the 10-tooth count and pinion diameter; another module changes tooth pitch even when the number of teeth is unchanged. The old starter or ring-gear specification should therefore support the module match before a substitute is accepted.

How should a distributor confirm 428000-6030 replenishment during fitment review?

For aftermarket product managers reviewing customer demand, keep 428000-6030, 12V, 2.7kW, 10T, the application description and the agreed packaging on the same replenishment line. Add dated photos when the equipment fleet changes or a different unit taken from service appears. This gives purchasing and warehouse teams enough detail to avoid silently merging a new version into established stock.

Which comparison prevents a mismatch for 428000-6030 among CASE versions when the starter being replaced is available?

For engine-parts specialists preparing an OE-based quote, 428000-6030 should remain separate from another CASE starter whenever voltage, output, tooth count, module, flange geometry or terminal position changes. For this line, retain 12V, 2.7kW and 10T together in the purchasing description. That specification bundle gives sales, warehouse and technical teams one consistent basis for reviewing alternatives.

Which comparison prevents a mismatch for 428000-6030 carton identification when the removed unit is available?

For regional parts suppliers requesting production pricing, ask that unit and carton labels repeat the agreed reference, 12V, 2.7kW and 10T where the packaging format permits. Add the customer's barcode and destination marks before production. Clear identification allows distributors to receive, bin and pick this version without opening packaging or relying on a generic starter description.

Request a Wholesale Quote for 428000-6030 Construction Equipment Starter Motor

For aftermarket wholesalers setting packaging requirements, discuss a 428000-6030 supply program with Elecdura by sending the OE reference, application, annual or initial quantity, destination and branding needs. The reply will identify the offered product version and agreed commercial options.