26338 Case 580G Starter Motor Wholesale Supply

26338 Case 580G Starter Motor Procurement Overview

26338 for Case 580G is presented for wholesale enquiries with the listed 12V, 2.8kW and 10T specification. That precise identity gives commercial buyers a practical starting point for checking fit, availability, packing and delivery without relying on a broad starter-family description.

For distributor or fleet orders, combine 26338 with the relevant Case 580G serial, engine or machine information available. Include quantity, destination, target arrival date and photographs of the removed starter; the sales response can then address the exact requirement and commercial schedule.

26338 Starter Motor Specifications for B2B Orders

The fastest useful fit check is a paired view of drive-end housing, mounting angle, 10T pinion and the 40 mm reference and the side profile. Keep the old starter and proposed sample in the same orientation, then compare the locating shoulder and pinion position. This creates a reusable reference for later branch orders.

A correct replacement must satisfy both the 12V 2.8kW electrical requirement and the 10T drive specification. Inspect the control-terminal connection and battery-cable route as part of the fit check rather than treating them as an after-installation detail.

26338 Cross-Reference Handling for Wholesale Supply

A mixed-reference enquiry should show 26338 and every alternative on separate lines, each tied to its own photo or source. Elecdura can then compare the candidates with the Case 580G requirement without implying that all listed numbers are automatically interchangeable.

For this backhoe requirement, purchasing teams should quote machine-service dealers with packing and delivery options matched to jobsite urgency. Keep the confirmed Case 580G details, product photographs and received lot beside the item record so a later order can be compared with the same physical and commercial reference.

26338 B2B Starter Motor Supply for Case 580G

Wholesale buyers may combine an initial verification order with a forward replenishment plan, provided each reference remains clearly separated. Normal terms are MOQ 20 pieces, 7–15 days after confirmation and an 18-month warranty; packing and freight are quoted for the stated destination.

Stock planning should reflect the operating pattern behind this item: it serves Case 580G backhoe parts programs where downtime affects both loader and excavating work. Separate trial pieces, routine shelf stock and urgent service demand, then state whether cartons or labels must be divided by branch, customer or project.

This video shows Elecdura production and electrical-testing capability for starter-motor supply. It supports supplier evaluation; the 26338 order should still be based on the listed application, electrical data and physical unit checks.

26338 Case 580G Starter Motor FAQs

When the removed starter is available, how should 12V be confirmed for 26338?

Check the machine electrical system, old-starter label and service record before ordering. Keep 2.8kW, 10T and the terminal arrangement in the same comparison. A starter can have a similar flange but the wrong voltage, output or cable layout, so these facts should be confirmed together. This keeps the check specific to 26338, not the general housing family.

When the removed starter is available, which physical details matter most when comparing 26338?

Compare drive-end housing, mounting angle, 10T pinion and the 40 mm reference with the removed starter, using a straight flange view and a side view parallel to the shaft. Also inspect the locating surface and drive projection. Matching only paint, motor diameter or one mounting ear can hide a difference that affects installation or pinion engagement. This keeps the check specific to 26338, not the general housing family.

A common Case 580G purchasing question: Is a matching 10T pinion enough to approve 26338?

No. Tooth count is only one control. The locating face, mounting pattern, pinion reach, 40 mm reference, solenoid position, terminals and 12V system must also agree with the removed starter. Review the full set before a sample or bulk order is accepted. The 26338 result should remain traceable to the 12V 2.8kW 10T configuration.

Distributor check: What should be checked before installing a 26338 starter?

Load-test the battery, measure voltage drop on positive and ground circuits, inspect cable lugs and confirm the engine turns freely. Check the ring gear and mounting-ground contact as well. These steps help separate a starter concern from weak batteries, high resistance or mechanical drag that can produce similar symptoms. Retain the 2.8kW 10T specification with the 26338 decision.

When the removed starter is available, what should receiving staff inspect on a 26338 shipment?

Confirm carton count, labels and visible condition before sampling. On selected units, compare the pinion, mounting face, solenoid and terminals with the confirmed record. Isolate any damaged or different unit with carton and lot photographs before the remainder is released to normal Case 580G inventory. This keeps the check specific to 26338, not the general housing family.

Distributor check: Why should Case 580G stay on the 26338 order line?

The application gives purchasing and receiving teams context that a reference alone may not provide. Keeping Case 580G, the electrical rating, pinion and confirmed photographs together makes repeat ordering clearer and reduces the chance that a visually related starter from another machine or engine family is substituted. Retain the 2.8kW 10T specification with the 26338 decision.

When the removed starter is available, how should alternate references for 26338 be handled?

List every complete alternate on a separate RFQ line and state whether it came from a label, invoice or parts record. Compare voltage, output, pinion, mounting and terminals before treating it as interchangeable. If one point remains uncertain, request a separate offer instead of combining the numbers. This keeps the check specific to 26338, not the general housing family.

What lead-time details should be stated for a 26338 order?

Tell Elecdura the quantity, destination, required arrival date and whether the demand supports an urgent repair, normal replenishment or a planned project. Normal preparation is 7–15 days after confirmation, but freight and packing choices depend on the actual schedule and shipment size. Apply the result to the 26338 Case 580G line rather than an unrelated starter family.

Ask for 26338 B2B Starter Motor Supply Terms

Email info@elecdurauto.com with 26338, Case 580G details, old-unit photographs, quantity, delivery country and required date. Elecdura will reply with the matching 12V 2.8kW 10T offer, availability, packing, lead time and freight options.