JCB 220 12V 2.0kW 13T Starter Motor

JCB 220 12V 2.0kW 13T Construction Equipment Starter Motor for JCB 220

For purchasing teams planning mixed-model inventory, JCB 220 12V 2.0kW 13T is an aftermarket construction equipment starter motor for JCB 220. Its 12V system, 2.0kW output and 13T pinion give construction-equipment parts distributors, importers and fleet suppliers a clear product definition for OE-reference replacement and repeat-order sourcing.

For distributors updating a customer item master, accurate version control reduces avoidable returns and mixed stock. The gallery, technical drawing where available, and order information below give commercial and technical teams a shared basis for the RFQ.

JCB 220 12V 2.0kW 13T Starter Motor Specifications and Technical Drawing

For application specialists preparing an OE-based quote, because no dimensional drawing is available for this version, the approved product views, full reference and 12V 2.0kW 13T specification should be compared with the starter being replaced. Customer measurements can then complete the fitment review without introducing unverified dimensions.

For replacement-parts sellers separating similar housings, A dimensional drawing was not supplied for JCB 220 12V 2.0kW 13T. For a fitment enquiry, provide straight-on images of the mounting face and drive end plus the locating diameter, hole spacing, pinion projection and terminal direction measured from the starter being replaced.

JCB 220 12V 2.0kW 13T Aftermarket Replacement and Application

For technical buyers checking version-defining data, JCB 220 is the stated application for JCB 220 12V 2.0kW 13T. Buyers comparing JCB 220 12V 2.0kW 13T should confirm that the starter being replaced shares the same 12V system, 2.0kW output and 13T drive before adding the item to a distributor order.

For engine-parts specialists confirming electrical ratings, A direct replacement decision should combine the OE group with physical comparison. Check the mounting face, 13T drive and cable-stud direction, and ask for a separate review when one of those features differs.

JCB 220 12V 2.0kW 13T Wholesale Supply for Distributors and Importers

For regional parts suppliers setting packaging requirements, wholesale enquiries for JCB 220 12V 2.0kW 13T can combine product matching with packaging and inspection planning. Elecdura offers neutral packaging and private-label review for qualified orders, with 20 pcs MOQ, 7–15 days subject to confirmation and an 18-month warranty under agreed terms.

For aftermarket wholesalers planning replenishment, Elecdura can align product identification, electrical testing and packaging records with the buyer's order. The exact inspection scope depends on the agreed quantity and market requirements and should be stated before production planning.

JCB 220 12V 2.0kW 13T Starter Motor Buyer FAQ

What should purchasing verify first for 12V system compatibility for a first B2B purchase?

For maintenance suppliers confirming electrical ratings, JCB 220 12V 2.0kW 13T is a 12V starter and must be connected only to the matching machine electrical system. Read the voltage marking on the old unit and verify the battery arrangement ahead of the order. A housing can look correct while the winding and solenoid are designed for another voltage, so appearance must not override the electrical label.

What should purchasing verify first for JCB 220 12V 2.0kW 13T carton identification before accepting a substitute?

For private-label buyers setting packaging requirements, ask that unit and carton labels repeat the agreed reference, 12V, 2.0kW and 13T where the packaging format permits. Add the customer's barcode and destination marks before production. Clear identification allows distributors to receive, bin and pick this version without opening packaging or relying on a generic starter description.

Which detail separates JCB 220 12V 2.0kW 13T rear-terminal photograph when checking a replacement proposal?

For purchasing teams matching the old starter, use the rear view of JCB 220 12V 2.0kW 13T to identify battery and signal terminals, their direction and the clearance around each stud. Match the customer's photograph from the same orientation and consider cable routing in JCB 220. A correct drive end with an unusable terminal position is not a complete fitment match.

Which detail separates mounting face, locating shoulder and bolt positions before a purchase order is released?

For distributors reviewing drive-end geometry, no dimensional drawing is supplied, so measure the old unit's mounting face, locating shoulder and bolt positions. Take each measurement from the same face shown or described, then compare the locating shoulder, bolt pattern and drive-end projection as one set. A single matching diameter is not enough if the hole pattern or axial reach places the pinion differently.

Which check should lead mounting-hole pattern during an application review?

For technical buyers preparing an OE-based quote, A complete mounting-hole callout is not stated for JCB 220 12V 2.0kW 13T. Photograph the old flange straight on and provide hole count, bore diameter and center spacing from the same datum. Those measured points let purchasing separate close housings without transferring hole data from another starter or assuming that a similar silhouette will bolt in.

Which specification deserves priority for JCB 220 12V 2.0kW 13T replenishment before comparing delivery options?

For engine-parts specialists requesting production pricing, keep JCB 220 12V 2.0kW 13T, 12V, 2.0kW, 13T, the application description and the agreed packaging on the same replenishment line. Add dated photos when the equipment fleet changes or a different unit taken from service appears. This gives purchasing and warehouse teams enough detail to avoid silently merging a new version into established stock.

Which detail separates JCB 220 12V 2.0kW 13T ring-gear engagement when checking a replacement proposal?

For fleet-parts buyers evaluating a direct replacement, review the 13T pinion, module 2.54, rest position and available axial dimensions as one engagement set. Inspect the ring gear for wear before fitting. A correct bolt pattern cannot protect the gear if pitch or projection differs, so drive geometry should be resolved before the starter is energized.

What must be matched before quoting JCB 220 12V 2.0kW 13T before stock is assigned?

For technical sales teams comparing the flange and terminals, JCB 220 12V 2.0kW 13T should be treated as one inquiry group only after the starter being replaced is compared. Ask the customer for the complete label and clear views of the drive end, flange and terminals. If a suffix, housing shape or terminal clocking differs, keep it as a separate commercial line instead of assuming that the shared number guarantees interchangeability.

Request a Wholesale Quote for JCB 220 12V 2.0kW 13T Construction Equipment Starter Motor

For sourcing managers reviewing customer demand, discuss a JCB 220 12V 2.0kW 13T supply program with Elecdura by sending the OE reference, application, annual or initial quantity, destination and branding needs. The reply will identify the offered product version and agreed commercial options.