19747 Komatsu Starter Motor 12V 2.5kW 11T

19747 Komatsu Starter Motor Sourcing Control for Wholesale Buyers

B2B approval of 19747 starts with the 12V, 2.5kW, 11-tooth clockwise configuration and the stated use in Komatsu vehicles and equipment cross-referenced to 19747. Confirm the complete label, flange, drive-end geometry, pinion and terminal position before a sample or production lot is released for the buyer's stock.

The distributor record for 19747 should connect the reference group 19747 / 128000-9970 with Komatsu vehicles and equipment cross-referenced to 19747. Add the old-unit label, mounting-face image, terminal view and receiving result to that record. Reuse it for repeat quotations, but create a new revision whenever the supplier changes the suffix, housing, pinion or electrical rating. A disciplined record reduces avoidable substitutions during urgent replenishment.

19747 Starter Motor B2B Production and Test Video for Wholesale Supply

This video introduces Elecdura starter-motor production and supply capabilities. Use the specification, cross-reference details and fitment checks on this page when evaluating 19747.

19747 Starter Motor Distributor Specifications for Distributor Sourcing

19747 Starter Motor OE Cross-Reference Review for Bulk Procurement

Use 19747 as the primary purchasing reference and cross-check 128000-9970. These numbers identify the candidate starter family, but approval still requires the exact suffix, electrical rating, drive end, mounting geometry, pinion and terminal layout to match the removed unit or signed sample.

19747 Starter Motor Bulk Fitment Approval for B2B Supply

Confirm the complete 19747 / 128000-9970 group together with the 12V, 2.5kW, 11-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance against the removed unit or approved sample and keep the signed sample with the purchase record.

19747 Starter Motor Wholesale Receiving Inspection for Aftermarket Buyers

For a wholesale shipment, sample units across the 19747 lot rather than inspecting only the top carton. Compare electrical rating, drive-end geometry, mounting bores, terminal position, housing protection and lot identity with the approval record and document pass, fail and hold quantities. Do not mix a disputed suffix or drive-end version with cleared stock, even when the outer housing looks alike.

19747 Starter Motor MOQ and Private-Label Supply for Fleet Replacement

19747 Starter Motor Distributor FAQ for Wholesale Supply

Which mounting details should be compared before ordering 19747?

Compare the machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance with the removed starter. Check bolt-hole spacing, locating diameter, starter clocking, pinion rest position and rear-terminal clearance instead of judging from the outer housing alone. Never pull a misaligned unit into place with mounting bolts. A measured or photographed fitment record is especially valuable when nearby references share the same voltage and tooth count but use another drive-end or solenoid orientation.

Which incoming-inspection points matter for 19747?

Tie every carton and sampled unit to 19747, the approved cross-reference set and the supplier lot. Inspect electrical rating, drive-end geometry, mounting bores, terminal position, housing protection and lot identity, then measure and compare the sampled unit with the signed photos or dimensional record. Record pass and fail quantities before the stock is mixed. Quarantine any different rating, pinion, mounting face or terminal layout, because a fitment error can immobilize a machine, trigger emergency freight and extend paid downtime on site. This receiving discipline is cheaper than sorting returns after distribution.

Can a similar 12V starter replace 19747?

A substitute is acceptable only when its complete OE relationship, 12V system, 2.5kW rating, 11T, rotation and mounting geometry agree with the approved unit. Similar appearance or a shared partial number is not enough. Ask for application and old-unit details, then test or approve a sample before changing the purchase line. Keep materially different versions separate in inventory so warehouse staff cannot fulfil one inquiry with the wrong variant.

How can buyers separate a 19747 fault from an equipment fault?

Check battery bank balance, cranking voltage, cable and ground drop, control relay, ring gear and engine drag before condemning the starter. Record battery voltage at rest and during the start command, then measure voltage drop under load; a weak supply or poor ground can imitate starter failure. Inspect the mounting surface and gear engagement as well. Attach these results, the old-unit label and failure symptoms to the claim so the supplier can distinguish a product defect from an upstream electrical or mechanical problem.

What makes a 19747 RFQ technically complete?

Send 19747 and all visible OE numbers, the full application or engine record, required quantity, destination and target delivery date. Add clear photos of the label, drive end, mounting face and terminals, plus any dimensional drawing available. State packaging, private-label, sample and inspection requirements at the start. A technically complete RFQ lets the supplier quote one verified configuration and reduces clarification delays after price approval.

How are MOQ, samples and repeat orders managed for 19747?

The standard MOQ is 20 pieces, subject to final order confirmation, and a sample or pre-production approval should precede volume release when fitment evidence is incomplete. Mark the signed-off sample with 19747, buyer application and revision date. Repeat orders should reference that same approval plus any packaging specification. If the supplier, suffix or physical design changes, treat it as a new approval rather than assuming the previous decision still applies.

Can 19747 be supplied with private-label packaging?

Neutral packaging and private-label review are available for qualified orders. The carton and inner protection should prevent movement, terminal damage and contamination while keeping the product reference, lot identity and quantity readable. Private-label artwork must not remove the technical identifiers used for fitment and claims. Agree label content, barcode needs, carton strength and destination handling before production so the packaging supports both sales presentation and receiving control.

How can distributors reduce disputes on 19747 claims?

The standard warranty is 18 months under agreed sales terms, but a claim still needs traceable evidence. Record the invoice or lot, installed application, old and supplied references, installation date, symptoms and electrical test results. Include photographs of the unit, terminals, mounting and pinion. Do not dismantle or discard the product before instructions are agreed. Complete evidence speeds technical review and prevents a battery, wiring or ring-gear problem from being misclassified.

Which OE numbers should a distributor match for 19747?

Use 19747 as the control reference and compare the complete group 19747 / 128000-9970. A cross-reference narrows the candidate, but it does not prove that every suffix has the same rating or mounting. Keep the removed-unit label, drive-end photograph, mounting-face view and rear-terminal view in the approval file, then connect that evidence to one quotation and purchase line so repeat orders remain traceable.

Request a B2B Quote for 19747 Starter Motors

Send the complete reference, Komatsu vehicles and equipment cross-referenced to 19747, old-unit photos, quantity, destination and packaging or inspection requirements. Elecdura will use that evidence to review one defined aftermarket starter configuration for your quotation.