228000-3850 Isuzu 4LE1 Starter Motor B2B Supplier

228000-3850 Starter Motor Selection for Professional B2B Buyers

228000-3850 supports Isuzu 4LE1 and Hitachi equipment using 3LD1-family industrial diesel starter references. It is positioned for professional replacement supply where the buyer needs the correct unit to arrive, install and remain repeatable across later orders; the fixed electrical release is 12V, 2.0kW, 9T and CW.

The Isuzu 4LE1 and 3LD1 labels can appear across stationary and mobile equipment, so the engine identity must be paired with the exact 897 or Denso number rather than equipment type alone. Generator-set and excavator customers should retain the label photograph with the nine-tooth drive record, since enclosure access, harness reach and switch-stud orientation affect serviceability after the starter reaches the job site. A reliable order file should state exactly how the unit was separated from its neighbors: Confirm the 4LE1/3LD1 engine plate, nine teeth and 12V 2.0kW rating, then compare the two Ø13 mm holes, 120 mm reference, 19 mm offset and switch stud orientation.

228000-3850 Starter Motor Specification Matrix and Technical Drawing

For purchasing and distribution-center quality staff, the key geometry is summarized in a single reference image below.

Confirm the 4LE1/3LD1 engine plate, nine teeth and 12V 2.0kW rating, then compare the two Ø13 mm holes, 120 mm reference, 19 mm offset and switch stud orientation. The image is a fitment reference and should be checked against the original unit on the repair bench or controlled warehouse sample rather than scaled from the screen.

228000-3850 Isuzu / Hitachi Application Control for Wholesale Supply

Cross-reference breadth is useful only when it does not erase the version boundary. For 228000-3850, the principal buying identifiers include 228000-3850, 228000-3851, 228000-3852, DSN2063, 8971128650, while Isuzu 4LE1 and Hitachi equipment using 3LD1-family industrial diesel starter references defines the working application scope.

Confirm the 4LE1/3LD1 engine plate, nine teeth and 12V 2.0kW rating, then compare the two Ø13 mm holes, 120 mm reference, 19 mm offset and switch stud orientation. If any of those points disagree, quote the alternatives separately instead of presenting a broad universal-fit claim.

• Application limit: Isuzu 4LE1 and Hitachi equipment using 3LD1-family industrial diesel starter references.

• Mismatch control: The Isuzu 4LE1 and 3LD1 labels can appear across stationary and mobile equipment, so the engine identity must be paired with the exact 897 or Denso number rather than equipment type alone. Generator-set and excavator customers should retain the label photograph with the nine-tooth drive record, since enclosure access, harness reach and switch-stud orientation affect serviceability after the starter reaches the job site. Confirm the 4LE1/3LD1 engine plate, nine teeth and 12V 2.0kW rating, then compare the two Ø13 mm holes, 120 mm reference, 19 mm offset and switch stud orientation.

• Distributor traceability: industrial-engine, excavator and generator-parts distributors should retain 228000-3850, 228000-3851, 228000-3852, DSN2063, 8971128650 with the accepted physical comparison and customer requirement.

For Isuzu / Hitachi 4LE1 / 3LD1 sourcing, the retained geometry combines 2 × Ø13 mm mounting holes, 120 mm mounting reference, Ø95 mm drive-end reference and 19 mm axial reference. Additional service identifiers include 8971128651, 8971128652, S6278, 19907N. A quotation for this line should arrive with engine model and serial, 897 or 228000 number, equipment make/model, mounting-face image, terminal image and order quantity; that information lets industrial-engine, excavator and generator-parts distributors distinguish this configuration before stock is committed.

For Isuzu industrial engines, a 4LE1 equipment record and a 3LD1 service record should not be merged until the 8971128650-series identity, nine-tooth drive and round two-hole face agree.

228000-3850 Starter Motor Warehouse Release and Order Support

Read the Isuzu label on sampled units, count nine teeth, compare the round face and inspect terminal insulators before assigning stock to Hitachi or industrial-engine accounts. Add carton condition, terminal protection and pinion protection to the receiving record because transit damage can create the same customer downtime as a wrong fitment.

Commercial preparation includes sample confirmation, 20-piece starting MOQ, order-specific lead-time review and neutral or qualified private-label packing. The carton label should carry the exact OE and 9T configuration, not a broad brand-only description.

The embedded production video supports supplier qualification for wholesale programs. The commercial release for this item remains tied to 228000-3850, 12V, 2.0kW, 9T and the confirmed mounting arrangement.

228000-3850 Starter Motor FAQ for B2B Procurement

For 4LE1 / 3LD1, which identifiers should be used to request 228000-3850?

In the 4LE1 / 3LD1 228000-3850 identity file, start with the fully stated 228000-3850 or a full matching reference such as 228000-3850, 228000-3851, 228000-3852, DSN2063, then add the 4LE1 / 3LD1 or machine record. For this Isuzu / Hitachi number set, shortened numbers can point to more than one service version. Within the 228000-3850 sourcing record, a useful inquiry also includes the mounting-face and cable point photographs so the manufacturer can identify the 9T, 12V configuration without relying on the model name alone. For the Isuzu / Hitachi 4LE1 / 3LD1 item, the usable identity chain is 228000-3850, 228000-3851, 228000-3852, DSN2063.

For 4LE1 / 3LD1, what separates this 4LE1 / 3LD1 starter from a nearby alternative?

For the 4LE1 / 3LD1 fitment, the Isuzu 4LE1 and 3LD1 labels can appear across stationary and mobile equipment, so the engine identity must be paired with the exact 897 or Denso number rather than equipment type alone. In this Isuzu / Hitachi application, generator-set and excavator customers should retain the label photograph with the nine-tooth drive record, since enclosure access, harness reach and switch-stud orientation affect serviceability after the starter reaches the job site. For the defined 228000-3850 scope, for this reason, the separating controls are 9T, 2.0kW, the mounting geometry and cable point position. For the 4LE1 / 3LD1 fitment, a importer should place those points on the approval unit sheet and catalog item record. In this Isuzu / Hitachi application, if a neighboring starter differs at any one of them, it should remain a separate quotation and warehouse line. For 4LE1 / 3LD1, the version boundary is 9T, 2.0kW, 120 mm mounting reference and the complete OE group.

For 4LE1 / 3LD1, how should the 9T pinion be verified?

At the 9T drive check, rotate the pinion enough to count every tooth clearly and take a close photograph before installation. For the 228000-3850 pinion review, compare the count with 9T and inspect the gear outside diameter, rest position and nose clearance against the removed starter. Within the 4LE1 / 3LD1 drive record, do not infer tooth count from a similar housing or an abbreviated cross-reference, because a one-tooth difference can prevent correct engagement. The Isuzu / Hitachi release uses 9T with CW rotation, so both details belong on the sample and carton checks.

For 4LE1 / 3LD1, which mounting details matter for 228000-3850?

During mounting review for 228000-3850, check the 4LE1/3LD1 engine plate, nine teeth and 12V 2.0kW rating, then compare the two Ø13 mm holes, 120 mm reference, 19 mm offset and switch stud orientation. At the 4LE1 / 3LD1 flange check, the technical graphic is a purchasing reference rather than a drawing to scale, so the starter taken from service or approval unit remains the final physical comparator. For the Isuzu / Hitachi installation comparison, record the mounting-hole arrangement, locating diameter, nose depth and solenoid clocking together; matching only one dimension is not enough for a volume release. For 4LE1 / 3LD1, the drawing controls are 2 × Ø13 mm mounting holes, 120 mm mounting reference, Ø95 mm drive-end reference and 19 mm axial reference.

For 4LE1 / 3LD1, can 228000-3851 be consolidated into the same stock code?

Within the Isuzu / Hitachi interchange group, it can be reviewed within the 228000-3850 reference family, but consolidation should occur only after the 12V, 2.0kW, 9T, rotation, flange face and cable points agree. For the 228000-3850 cross-reference decision, keep suffixes visible during quotation and approval unit review. In the 4LE1 / 3LD1 stocking boundary, once a measured approval unit is signed, store the accepted cross-reference list with the SKU so later trade customers use the same boundary. The working scope is Isuzu 4LE1 and Hitachi equipment using 3LD1-family industrial diesel starter references; it is not a universal statement for every Isuzu / Hitachi machine.

For 4LE1 / 3LD1, what application information is needed for this Isuzu / Hitachi starter?

For this industrial-engine, excavator and generator-parts distributors inquiry, provide the equipment or vehicle model, engine designation 4LE1 / 3LD1, production year or serial information where available, and the fully stated old-starter number. When quoting 228000-3850, the Isuzu 4LE1 and 3LD1 labels can appear across stationary and mobile equipment, so the engine identity must be paired with the exact 897 or Denso number rather than equipment type alone. For the Isuzu / Hitachi commercial request, generator-set and excavator customers should retain the label photograph with the nine-tooth drive record, since enclosure access, harness reach and switch-stud orientation affect serviceability after the starter reaches the job site. For this industrial-engine, excavator and generator-parts distributors inquiry, these details let the manufacturer narrow the application before the physical check and reduce the risk of approving a visually similar unit for a different engine or production change. A practical 4LE1 / 3LD1 inquiry includes engine model and serial, 897 or 228000 number, equipment make/model, mounting-face image, terminal image and order quantity.

For 4LE1 / 3LD1, how should a first 228000-3850 shipment be inspected?

At incoming inspection for 228000-3850, read the Isuzu label on sampled units, count nine teeth, compare the round face and inspect cable point insulators before assigning stock to Hitachi or industrial-engine accounts. During the 4LE1 / 3LD1 lot release, open cartons from more than one pallet position, compare labels and castings, and inspect cable point insulation and pinion protection. For Isuzu / Hitachi warehouse acceptance, keep photographs of accepted units with the receiving record. At incoming inspection for 228000-3850, if a tooth count, flange, nose or connection differs, quarantine the affected cartons before branch allocation or customer dispatch. The receiving release for this Isuzu / Hitachi starter is the combined 9T, 2 × Ø13 mm mounting holes and terminal check.

For 4LE1 / 3LD1, what should be included in a wholesale RFQ?

For the 228000-3850 supply program, send engine model and serial, 897 or 228000 number, equipment make/model, mounting-face image, cable point image and order quantity, together with the requested quantity, destination, target timing and packaging preference. When preparing the 4LE1 / 3LD1 order, state whether a approval unit is required and identify any mixed references on separate lines. For this Isuzu / Hitachi distributor line, this gives Elecdura enough commercial and technical context to check the exact 228000-3850 configuration before price, lead time and private-label details are finalized. The 4LE1 / 3LD1 commercial request should retain 228000-3850, 12V, 2.0kW, 9T, quantity, destination and packaging preference on one line.

Discuss 228000-3850 Starter Motor Samples and program quantity

Send engine model and serial, 897 or 228000 number, equipment make/model, mounting-face image, terminal image and order quantity, required quantity, destination and packaging preference. Elecdura will review the 12V, 2.0kW, 9T 228000-3850 configuration and confirm sample, lead-time and wholesale-supply details before the order is released.