Your Whole New Supply Chain For Heavy-Duty Parts
Whatsapp：
+86 18915027366
Phone：
+86 18915027366
24V 4.5kW 11T 40mm RH
Elecdura
Available for qualified orders
20 pcs
7 - 15 Days
Neutral packaging / private-label review
18 Months
ND Type RH Starter Configuration; 24V, 4.5kW, 11T, 40mm pinion reference
Confirm 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation, 24V, 4.5kW, solenoid position and terminal layout against the removed starter before volume supply.
| Quantity: | |
|---|---|
The 24V 4.5kW 11T 40mm RH starter for ND Type RH Starter Configuration is intended for replacement demand. It combines 24V, 4.5kW output with the 11T drive, allowing B2B buyers to keep the quotation tied to one application and physical configuration rather than a broad visual description.
Branch inventory manager teams handling tender quotation should send 24V 4.5kW 11T 40mm RH, the ND Type RH Starter Configuration record, required quantity, destination and delivery timing together. Add straight drive-end and terminal-side photographs of the removed starter. Elecdura can then address more reliable receiving checks, repeat-order carton marks and the correct physical configuration in one useful commercial offer.
| Primary order identity | 24V 4.5kW 11T 40mm RH |
| Target application | ND Type RH Starter Configuration |
| Starter design | ND-type replacement |
| System voltage | 24V |
| Rated output | 4.5kW |
| Pinion identification | 11T / 40mm reference |
| OE / reference group | Application and physical unit details |
| Wholesale terms | MOQ 20 pcs / normally 7–15 days after order confirmation |
| Warranty | 18 months under agreed sales terms |
The key fit controls are 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation. Compare them as one geometry set, then check the locating face and drive projection against the removed starter. This is more reliable than matching one bolt hole or using an angled marketplace photograph.
A correct replacement must satisfy both the 24V 4.5kW electrical requirement and the 11T drive specification. Inspect the control-terminal connection and battery-cable route as part of the fit check rather than treating them as an after-installation detail.
A mixed-reference enquiry should show 24V 4.5kW 11T 40mm RH and every alternative on separate lines, each tied to its own photo or source. Elecdura can then compare the candidates with the ND Type RH Starter Configuration requirement without implying that all listed numbers are automatically interchangeable.
For tender quotation, keep 24V 4.5kW 11T 40mm RH, ND Type RH Starter Configuration, 24V, 4.5kW and 11T on one purchasing record. At goods-in, review voltage marking and battery setup before releasing the lot. This gives the branch inventory manager a documented basis for more reliable receiving checks when the next order is raised.
For qualified B2B orders, the normal MOQ is 20 pieces and preparation is usually 7–15 days after the order is confirmed. Elecdura can discuss neutral cartons, private-label review, export documents and an 18-month warranty according to the agreed quotation.
Demand from an independent diesel repair hub should keep 24V 4.5kW 11T 40mm RH tied to ND Type RH Starter Configuration. For tender quotation, the branch inventory manager can use a branch-specific reorder point, keep the flange measurement sheet and review voltage marking and battery setup at goods-in. This supports more reliable receiving checks while keeping repeat-order carton marks visible.
The video below introduces Elecdura starter-motor production and electrical testing for B2B supply. Buyers can review factory capability while using the 24V 4.5kW 11T 40mm RH application and specification shown above for their own product comparison.
Branch inventory manager teams should tie 24V 4.5kW 11T 40mm RH to ND Type RH Starter Configuration, 24V, 4.5kW, 11T and the removed-unit photographs before requesting price. For tender quotation, state quantity, destination and delivery timing, then review voltage marking and battery setup. Ask Elecdura to address repeat-order carton marks and more reliable receiving checks in the same quotation.
Compare 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation with the removed starter, using a straight flange view and a side view parallel to the shaft. Also inspect the locating surface and drive projection. Matching only paint, motor diameter or one mounting ear can hide a difference that affects installation or pinion engagement. File 24V 4.5kW 11T 40mm RH with the voltage marking and battery setup check.
Load-test the battery, measure voltage drop on positive and ground circuits, inspect cable lugs and confirm the engine turns freely. Check the ring gear and mounting-ground contact as well. These steps help separate a starter concern from weak batteries, high resistance or mechanical drag that can produce similar symptoms. Use 24V 4.5kW 11T 40mm RH when arranging repeat-order carton marks.
Tell Elecdura the quantity, destination, required arrival date and whether the demand supports an urgent repair, normal replenishment or a planned project. Normal preparation is 7–15 days after confirmation, but freight and packing choices depend on the actual schedule and shipment size. This supports more reliable receiving checks for 24V 4.5kW 11T 40mm RH.
Confirm carton count, labels and visible condition before sampling. On selected units, compare the pinion, mounting face, solenoid and terminals with the confirmed record. Isolate any damaged or different unit with carton and lot photographs before the remainder is released to normal ND Type RH Starter Configuration inventory. Keep 24V 4.5kW 11T 40mm RH traceable through tender quotation.
Provide the invoice or lot reference, installation date, ND Type RH Starter Configuration details, service time and a clear description of the symptom. Include photographs of the flange, drive and terminals plus battery and voltage-drop results. Keep the unit assembled until Elecdura confirms the next step under the agreed terms. Link 24V 4.5kW 11T 40mm RH photographs to the voltage marking and battery setup record.
A sample is useful when the old label is incomplete, the application record is uncertain or several similar housings are in local stock. Confirm the sample against mounting, drive and electrical details before scaling the order. Keep the accepted photographs and measurements for later purchasing and receiving checks. Carry the 24V 4.5kW 11T 40mm RH result into repeat-order carton marks.
Low battery capacity, excessive voltage drop, corroded lugs, weak grounds, undersized cables and mechanical engine drag can all reduce cranking speed. Record loaded battery voltage and cable-drop readings before replacement. This protects the buyer from changing a starter while the original circuit problem remains. Retain 24V 4.5kW 11T 40mm RH for more reliable receiving checks and receiving review.
Email info@elecdurauto.com with 24V 4.5kW 11T 40mm RH, ND Type RH Starter Configuration details, old-unit photographs, quantity, delivery country and required date. Elecdura will reply with the matching 24V 4.5kW 11T offer, availability, packing, lead time and freight options.
