345-5671 Caterpillar Starter Motor 24V 6.0kW 10T

345-5671 Construction Equipment Starter Motor for CAT C7.1

For purchasing teams building a new starter range, 345-5671 is an aftermarket construction equipment starter motor for CAT C7.1. Its 24V system, 6.0kW output and 10T pinion give construction-equipment parts distributors, importers and fleet suppliers a clear product definition for OE-reference replacement and repeat-order sourcing.

For distributors requesting production pricing, the goal is a repeatable supply line: one agreed product identity, one packaging definition and one set of incoming checks. This is useful for importers building category coverage as well as fleet suppliers replenishing an existing starter reference.

345-5671 Starter Motor Specifications and Technical Drawing

For application specialists comparing the flange and terminals, the product identity combines 345-5671, CAT C7.1, 24V, 6.0kW and 10T. Keeping those facts together helps buyers separate this starter from adjacent versions.

For replacement-parts sellers reviewing a replacement proposal, the source-faithful technical drawing records the available mounting information for 345-5671, including 3×Ø13.5, 126.5 mm; use the printed values together with the product views because the drawing supports comparison and should not be scaled from the screen.

345-5671 Aftermarket Replacement and Application

For technical buyers matching the old starter, the replacement search starts with 345-5671, 428000-91211 and the CAT C7.1 application. For mixed fleets or previously repaired machines, add clear old-unit photos so a substituted starter does not become the only fitment evidence.

For engine-parts specialists reviewing drive-end geometry, product photos and the stated specifications should be reviewed together. If the old starter uses another pinion, mounting face or rear connection, keep that configuration on a separate RFQ until it is identified.

345-5671 Wholesale Supply for Distributors and Importers

For regional parts suppliers opening a first B2B purchase, distributor supply for 345-5671 can include neutral packaging, customer-brand review and order-specific labels. Current commercial guidance is 20 pcs MOQ, 7–15 days subject to confirmation and an 18-month warranty under agreed terms.

For aftermarket wholesalers confirming an incoming batch, Elecdura can align product identification, electrical testing and packaging records with the buyer's order. The exact inspection scope depends on the agreed quantity and market requirements and should be stated before production planning.

345-5671 Starter Motor Buyer FAQ

What should purchasing verify first for module 3.175 when checking a replacement proposal?

For maintenance suppliers reviewing drive-end geometry, module 3.175 is part of the gear geometry for 345-5671. Confirm it together with the 10-tooth count and pinion diameter; another module changes tooth pitch even when the number of teeth is unchanged. The old starter or ring-gear specification should therefore support the module match before a substitute is accepted.

Which specification deserves priority for CAT C7.1 previously replaced starter for warehouse identification?

For equipment-parts dealers comparing nearby starter versions, ask whether the starter removed from CAT C7.1 is original or an earlier replacement. If it has been substituted before, the visible unit may not represent the equipment's initial build. Use its label and geometry together with 345-5671, 24V, 6.0kW and 10T before turning that history into a bulk stocking decision.

How should a workshop distinguish 3×Ø13.5 when preparing a technical RFQ?

For purchasing teams preparing a technical RFQ, the drawing lists 3×Ø13.5 for 345-5671. Count the holes, measure their diameters and compare their positions from the locating face. A matching outer housing does not compensate for a hole pattern that will not seat squarely, so flange geometry should pass before the starter reaches the installation bay.

Which comparison prevents a mismatch for 345-5671 locating face during fitment review?

For distributors checking version-defining data, the 345-5671 flange should sit flat against the CAT C7.1 mounting surface without being pulled into place by the bolts. Clean both faces and compare the locating shoulder, hole pattern and any stated diameters. Rocking, a visible gap or bolt misalignment indicates that the version check is incomplete and installation should stop.

How can an importer validate 3×Ø13.5 and 126.5 mm before comparing delivery options?

For technical buyers comparing the flange and terminals, use the supplied technical drawing to compare 3×Ø13.5 and 126.5 mm. Take each measurement from the same face shown or described, then compare the locating shoulder, bolt pattern and drive-end projection as one set. A single matching diameter is not enough if the hole pattern or axial reach places the pinion differently.

How can an importer validate 10T and module 3.175 before accepting a substitute?

For engine-parts specialists reviewing a replacement proposal, the supplied drive uses 10 teeth with module 3.175. Count the old pinion teeth and compare outside diameter, rest position and engagement depth during pre-order review. The 3.175 module is part of the gear definition, so another pitch must not be combined on the same line. This check protects the ring gear from an incorrect mesh.

How should a workshop distinguish 345-5671 inquiry package for a documented fitment decision?

For regional parts suppliers updating a customer item master, A useful inquiry for 345-5671 includes quantity, destination, required date, CAT C7.1, the full old-unit number and clear photos of the label, drive end, mounting surface and cable studs. State neutral or private-label packaging needs at the same time. Elecdura can then quote the 24V, 6.0kW, 10T version against a complete item definition.

Which detail separates 345-5671 drive-end photograph when confirming the commercial line?

For technical sales teams checking application evidence, the drive-end image for 345-5671 should be used to count 10 teeth and compare the flange, locating shoulder and pinion rest position. Capture the existing starter with comparable framing and clear light. A profile photograph may not show the drive teeth and mounting points clearly; a frontal image is better for the final comparison.

Request a Wholesale Quote for 345-5671 Construction Equipment Starter Motor

For sourcing managers defining label requirements, send 345-5671, 428000-91211, the CAT C7.1 application, required quantity, destination and packaging preference. Add old-unit photos when available. Elecdura will review the 24V, 6.0kW, 10T version and prepare a product-specific wholesale quotation.