STY0001WA Cummins A2300 Engine in Doosan Starter Motor 12V 2.0kW 15T

STY0001WA Cummins A2300 Engine in Doosan Starter Motor Distributor Supply and Fitment Control

For repeat wholesale supply, STY0001WA should remain tied to Cummins A2300 engines in Doosan skid-steer and industrial equipment and the exact 12V, 2.0kW, 15-tooth clockwise configuration. Record the accepted old-unit label and physical sample so purchasing, receiving and warranty teams do not mix an adjacent starter variant with the approved item.

STY0001WA Starter Motor B2B Production and Test Video for Aftermarket Buyers

This video introduces Elecdura starter-motor production and supply capabilities. Use the specification, cross-reference details and fitment checks on this page when evaluating STY0001WA.

STY0001WA Starter Motor Distributor Specifications for Fleet Replacement

STY0001WA Starter Motor OE Cross-Reference Review for Wholesale Supply

Use STY0001WA as the primary purchasing reference and cross-check 19188N, 115968. These numbers identify the candidate starter family, but approval still requires the exact suffix, electrical rating, drive end, mounting geometry, pinion and terminal layout to match the removed unit or signed sample.

STY0001WA Starter Motor Bulk Fitment Approval for Distributor Sourcing

Confirm the complete STY0001WA / 19188N / 115968 group together with the 12V, 2.0kW, 15-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance against the removed unit or approved sample and keep the signed sample with the purchase record.

STY0001WA Starter Motor Wholesale Receiving Inspection for Bulk Procurement

For a wholesale shipment, sample units across the STY0001WA lot rather than inspecting only the top carton. Compare electrical rating, drive-end geometry, mounting bores, terminal position, housing protection and lot identity with the approval record and document pass, fail and hold quantities. Do not mix a disputed suffix or drive-end version with cleared stock, even when the outer housing looks alike.

STY0001WA Starter Motor MOQ and Private-Label Supply for B2B Supply

STY0001WA Starter Motor Distributor FAQ for Aftermarket Buyers

Where is STY0001WA commonly used, and what still needs confirmation?

Confirm the complete STY0001WA / 19188N / 115968 group together with the 12V, 2.0kW, 15-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance against the removed unit or approved sample and keep the signed sample with the purchase record.

What specification mismatch creates the greatest risk on STY0001WA?

Confirm the complete STY0001WA / 19188N / 115968 group together with the 12V, 2.0kW, 15-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance against the removed unit or approved sample and keep the signed sample with the purchase record.

Which configuration checks prevent a mismatched STY0001WA order?

Confirm the complete STY0001WA / 19188N / 115968 group together with the 12V, 2.0kW, 15-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance against the removed unit or approved sample and keep the signed sample with the purchase record.

Which mounting details should be compared before ordering STY0001WA?

Measure and compare the machine serial range, engine plate, mounting nose, pinion position, terminal clocking and installed clearance with the removed starter. Check bolt-hole spacing, locating diameter, starter clocking, pinion rest position and rear-terminal clearance instead of judging from the outer housing alone. Never pull a misaligned unit into place with mounting bolts. A measured or photographed fitment record is especially valuable when nearby references share the same voltage and tooth count but use another drive-end or solenoid orientation.

Which incoming-inspection points matter for STY0001WA?

Tie every carton and sampled unit to STY0001WA, the approved cross-reference set and the supplier lot. Inspect electrical rating, drive-end geometry, mounting bores, terminal position, housing protection and lot identity, then compare the sampled unit with the signed photos or dimensional document. Record pass and fail quantities before the stock is mixed. Quarantine any different rating, pinion, mounting face or terminal layout, because a fitment error can immobilize a machine, trigger emergency freight and extend paid downtime on site. This receiving discipline is cheaper than sorting returns after distribution.

Can a similar 12V starter replace STY0001WA?

A substitute is acceptable only when its complete OE relationship, 12V system, 2.0kW rating, 15T, rotation and mounting geometry agree with the approved unit. Similar appearance or a shared partial number is not enough. Ask for application and old-unit evidence, then test or approve a sample before changing the order line. Keep materially different versions separate in inventory so warehouse staff cannot fulfil one inquiry with the wrong variant.

How can buyers separate a STY0001WA fault from an equipment fault?

Check battery bank balance, cranking voltage, cable and ground drop, control relay, ring gear and engine drag before condemning the starter. Record battery voltage at rest and during the start command, then measure voltage drop under load; a weak supply or poor ground can imitate starter failure. Inspect the mounting surface and gear engagement as well. Attach these results, the old-unit label and failure symptoms to the claim so the supplier can distinguish a product defect from an upstream electrical or mechanical problem.

What makes a STY0001WA RFQ technically complete?

Send STY0001WA and all visible OE numbers, the full application or engine record, required quantity, destination and target delivery date. Add clear photos of the label, drive end, mounting face and terminals, plus any dimensional drawing available. State packaging, private-label, sample and inspection requirements at the start. A technically complete RFQ lets the supplier quote one verified configuration and reduces clarification delays after price approval.

How are MOQ, samples and repeat orders managed for STY0001WA?

The standard MOQ is 20 pieces, subject to final order confirmation, and a sample or pre-production approval should precede volume release when fitment information is incomplete. Mark the approved sample with STY0001WA, buyer application and revision date. Repeat orders should reference that same approval plus any packaging specification. If the supplier, suffix or physical design changes, treat it as a new approval rather than assuming the previous decision still applies.

Request a B2B Quote for STY0001WA Starter Motors

Send the complete reference, Cummins A2300 engines in Doosan skid-steer and industrial equipment, old-unit photos, quantity, destination and packaging or inspection requirements. Elecdura will use that evidence to review one defined aftermarket starter configuration for your quotation.