UD18487S Doosan Starter Motor 24V 4kW 11T

UD18487S Doosan Starter Motor Wholesale Supply for Distributors

For distributors and fleet-parts buyers, UD18487S identifies a 24V, 4kW, 11-tooth clockwise configuration for Doosan vehicles and equipment cross-referenced to UD18487S. Approve the complete reference, rating, drive end, mounting face, pinion and terminals against the removed unit or signed sample so a nearby version is not substituted into the purchasing line.

UD18487S should enter a wholesale catalog only after the buyer links UD18487S / 8200141 / 300516-00040A / 36100-52000 to Doosan vehicles and equipment cross-referenced to UD18487S and a verified sample. Record the mounting pattern, pinion reach, terminal clocking and rating label alongside the commercial terms. When another factory quotes the line, compare that complete record first; a lower price on an adjacent version does not represent the same purchasing outcome.

UD18487S Starter Motor B2B Production and Test Video for Aftermarket Buyers

This video introduces Elecdura starter-motor production and supply capabilities. Use the specification, cross-reference details and fitment checks on this page when evaluating UD18487S.

UD18487S Starter Motor Distributor Specifications for Fleet Replacement

UD18487S Starter Motor OE Cross-Reference Review for Wholesale Supply

Use UD18487S as the primary purchasing reference and cross-check 8200141, 300516-00040A, 36100-52000. These numbers identify the candidate starter family, but approval still requires the exact suffix, electrical rating, drive end, mounting geometry, pinion and terminal layout to match the removed unit or signed sample.

UD18487S Starter Motor Bulk Fitment Approval for Distributor Sourcing

Before accepting UD18487S as a replacement, obtain the full vehicle, machine or engine record and compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement. Cross-reference overlap is useful for finding the family, but it cannot replace a physical match. Store the approved label and four-angle photo set with the account so later orders use the same configuration.

UD18487S Starter Motor Wholesale Receiving Inspection for Bulk Procurement

Receiving control should link the carton, unit label and inspection sample to UD18487S. Verify reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability; photograph deviations and keep affected units separate while the supplier responds. Batch evidence makes repeat purchases more predictable and gives warranty teams a clear record if field feedback appears.

UD18487S Starter Motor MOQ and Private-Label Supply for B2B Supply

UD18487S Starter Motor Distributor FAQ for Aftermarket Buyers

Which reference numbers should buyers confirm for UD18487S?

Use UD18487S as the control reference and cross-check 8200141, 300516-00040A, 36100-52000. Retain the complete old-unit label plus drive-end, mounting-face and rear-terminal photos with the quotation and purchase line so repeat orders remain tied to the approved unit.

Which applications should buyers confirm for the UD18487S starter motor?

The specified application is Doosan vehicles and equipment cross-referenced to UD18487S. Because a model or engine family can include production changes, confirm the machine, vehicle or engine record and the complete old-unit suffix before promising fitment. Keep the approved record tied to one physical starter configuration.

Which electrical and drive specifications define UD18487S?

The specified configuration is 24V, 4kW, 11-tooth clockwise configuration. Voltage must match the electrical system, while power, tooth count and rotation affect cranking performance and ring-gear engagement. Put all four values on the sample-approval sheet and verify the physical pinion before releasing a distributor quantity.

Why is suffix-level verification important for UD18487S?

Confirm the complete UD18487S / 8200141 / 300516-00040A / 36100-52000 group together with the 24V, 4kW, 11-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

What physical fitment checks are required for UD18487S?

Compare the equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement with the removed starter. Check bolt-hole spacing, locating diameter, starter clocking, pinion rest position and rear-terminal clearance instead of judging from the outer housing alone. Never pull a misaligned unit into place with mounting bolts. A measured or photographed fitment record is especially valuable when nearby references share the same voltage and tooth count but use another drive-end or solenoid orientation.

What receiving checks protect a UD18487S bulk order?

Tie every carton and sampled unit to UD18487S, the approved cross-reference set and the supplier lot. Inspect reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability, then measure and compare the sampled unit with the signed photos or dimensional record. Record pass and fail quantities before the stock is mixed. Quarantine any different rating, pinion, mounting face or terminal layout, because an unverified substitute can stop equipment, generate a claim and turn a low unit price into a costly order. This receiving discipline is cheaper than sorting returns after distribution.

Should a visually similar starter be sold as UD18487S?

A substitute is acceptable only when its complete OE relationship, 24V system, 4kW rating, 11T, rotation and mounting geometry agree with the approved unit. Similar appearance or a shared partial number is not enough. Ask for application and old-unit details, then test or approve a sample before changing the purchase line. Keep materially different versions separate in inventory so warehouse staff cannot fulfil one inquiry with the wrong variant.

What should be diagnosed before replacing a UD18487S starter motor?

Check battery capacity, voltage drop, start signal, grounds, ring gear and mechanical engine load before condemning the starter. Record battery voltage at rest and during the start command, then measure voltage drop under load; a weak supply or poor ground can imitate starter failure. Inspect the mounting surface and gear engagement as well. Attach these results, the old-unit label and failure symptoms to the claim so the supplier can distinguish a product defect from an upstream electrical or mechanical problem.

How should a distributor request B2B pricing for UD18487S?

Send UD18487S and all visible OE numbers, the full application or engine record, required quantity, destination and target delivery date. Add clear photos of the label, drive end, mounting face and terminals, plus any dimensional drawing available. State packaging, private-label, sample and inspection requirements at the start. A technically complete RFQ lets the supplier quote one verified configuration and reduces clarification delays after price approval.

Request a B2B Quote for UD18487S Starter Motors

Send the complete reference, Doosan vehicles and equipment cross-referenced to UD18487S, old-unit photos, quantity, destination and packaging or inspection requirements. Elecdura will use that evidence to review one defined aftermarket starter configuration for your quotation.