243708145 Iveco 120EL18 Starter Motor Wholesale

243708145 Starter Motor B2B Fitment Guide for Iveco 120EL18 truck

Iveco commercial-vehicle distributors, fleet workshops and starter importers can source 243708145 for Iveco 120EL18 truck. Preserve the 10T pinion and 24V 4.5kW 10T module-3.175 Iveco 120EL18 specified configuration; do not substitute by engine family or housing appearance alone.

Send the full 243708145 application and old-unit identification rather than only a truck or engine brand. With mounting and terminal photos, quantity, destination and arrival target, Elecdura can discuss the correct starter, MOQ, packing, warranty and shipping route without unnecessary follow-up.

243708145 Starter Motor Drive-End Drawing for Aftermarket Distributors

Compare 243708145 at the illustrated complete starter mounting-hole layout, illustrated complete mounting-face pattern and illustrated locating-pilot shoulder profile. The illustrated pinion-side drive-end projection helps verify where the pinion sits relative to the flange, while a straight terminal-side photograph confirms whether the main and control connections remain accessible after installation.

For 243708145, count the 10T pinion and confirm module 3.175, CW rotation, 24V and 4.5kW. The terminal side and solenoid clearance must also agree with the installation. A different pinion or cable position should be quoted separately, even when major cross-references overlap.

243708145 Starter Motor Reference Group for Wholesale Sourcing

1. Search group: 243708145, 11010060 can help distributor teams locate the relevant starter family.
2. Order boundary: Confirm the complete reference with 24V, 4.5kW, 10T, CW, the drawing and terminal photographs before accepting one physical unit.

243708145 Starter Motor Distributor Stock and Delivery Support

MOQ begins at 20 pieces, with normal lead time of 7–15 days after order confirmation and an 18-month warranty under agreed terms. For 243708145, the offer can distinguish samples, available stock and production quantities while confirming carton protection and the shipment plan for the destination.

Stock planning should reflect the supported Iveco 120EL18 truck population, recent consumption and transfer time between service locations. Keeping 243708145, the 10T drive and the approved mounting interface visible in the inventory record reduces emergency substitution and improves later reorder accuracy.

This video introduces Elecdura production and electrical testing for starter motors supplied to distributors and service networks. The commercial offer for 243708145 continues to follow the stated application, electrical rating, pinion and mounting details so factory capability and product selection remain clearly connected.

243708145 Starter Motor Questions from Commercial Buyers

Which first-lot checks protect a distributor receiving 243708145 during an Iveco 120EL18 dealer receiving check?

For 243708145, count the cartons, compare labels and inspect selected units for flange, pinion and terminal damage. The sample should match illustrated complete starter mounting-hole layout, illustrated locating-pilot shoulder profile and the specified 10T drive. Hold any exception outside normal inventory until purchasing and the supplier agree on the correct disposition.

What workshop readings are useful when diagnosing a starting complaint involving 243708145 during an Iveco 120EL18 dealer electrical check?

Load-test the battery set and measure voltage drop on the positive and ground circuits while cranking. Inspect cable lugs, chassis grounds, the start-control signal and ring-gear condition before replacing 243708145. These checks distinguish a starter fault from low battery capacity, resistance or a control-circuit problem.

How can an importer avoid mixing 243708145 with a similar drive-end version during dealer sourcing?

For 243708145 in Iveco 120EL18 truck, confirm the machine or engine identity and read the full old-unit label. Check 10T, illustrated complete mounting-face pattern, illustrated locating-pilot shoulder profile and terminal orientation. Treat a different drive end or connector position as a separate item when the stated application overlaps.

When does a cross-reference related to 243708145 need a separate quotation in an Iveco 120EL18 dealer sourcing program?

Use the complete alternate number, not a shortened series, and attach photographs of the removed unit. The 243708145 group is acceptable only when 24V, 4.5kW, 10T, CW and the physical interface agree. A reference conflict should be clarified before samples or bulk quantities are released.

What physical controls belong on a first-lot check for 243708145 during an Iveco 120EL18 dealer inspection?

For 243708145, compare illustrated complete starter mounting-hole layout and illustrated complete mounting-face pattern in a straight front view, then illustrated locating-pilot shoulder profile and illustrated pinion-side drive-end projection in the side view. Add 10T, CW and terminal orientation; this is more reliable than an angled overall photograph.

How should Jubana distributors plan stock for 243708145 in an Iveco 120EL18 dealer program?

Plan 120EL18 stock by active fleet count, workshop consumption and delivery risk. Add recent usage, equipment population, transfer time and service level. Elecdura can then separate sample, emergency and replenishment quantities and plan packing or staged delivery around the buyer’s schedule.

What information should accompany a distributor RFQ for 243708145 in an Iveco 120EL18 dealer sourcing program?

A useful RFQ states 243708145, the machine or engine model, old-unit label, mounting and terminal photographs, requested quantity and delivery country. Include whether the demand is a sample, urgent service order or scheduled stock. Those details allow pricing to cover the correct unit and realistic shipping plan.

What evidence separates an electrical-system fault from a concern involving 243708145 in an Iveco 120EL18 dealer review?

For a service review of 243708145, identify the shipment and unit, describe the starting condition and record installation details. Add photographs of the drive, flange and terminals plus battery, ground and positive-cable test results. If the unit was removed, protect it from additional damage and retain it until the review is complete.

243708145 Start a Starter Motor Wholesale Enquiry

For a focused 243708145 quotation, share the machine or engine record, old-starter number, mounting and terminal images, order volume, delivery country and timing. You can email the RFQ directly to info@elecdurauto.com; Elecdura will reply with the matching specification, availability, packing and commercial terms.