28100-1170 Hino EH700/H07C 24V 4.5kW Starter Motor Wholesale Supply

28100-1170 Hino EH700/H07C Starter Motor B2B Purchasing Overview

For Hino EH700/H07C service, 28100-1170 is a focused wholesale line rather than a general starter listing. The 24V system, 4.5kW output and 11T drive identify one specific configuration. It supports Hino EH700/H07C purchasing where the 24V, 4.5kW and 11T identity must remain visible from quotation through receiving. Keep this purchase identity clear for quotation and repeat supply.

Import distributor teams handling engine-overhaul planning should send 28100-1170, the Hino EH700/H07C record, required quantity, destination and delivery timing together. Add straight drive-end and terminal-side photographs of the removed starter. Elecdura can then address consistent rebuild-bench identification, sample-to-bulk scheduling and the correct physical configuration in one useful commercial offer.

28100-1170 Starter Motor Wholesale Mounting and Electrical Checks

For sample confirmation, review 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation together with the overall drive-end reach. Measure or photograph the old unit on a flat surface where practical. Small differences at the flange or pinion can matter even when the motor and solenoid housings have similar proportions.

Electrical identity and mechanical fit must agree. Verify 24V, the 4.5kW rating and terminal layout, then count the 11 pinion teeth. A correct flange with the wrong system voltage, output or cable position is not an acceptable substitute.

28100-1170 Starter Motor OE Reference Control for B2B Orders

Use 28100-1170 as the primary searchable order identity. If the label or service record shows an alternate reference, list its complete format and source on a separate RFQ line until voltage, output, drive and mounting have all been compared.

For engine-overhaul planning, keep 28100-1170, Hino EH700/H07C, 24V, 4.5kW and 11T on one purchasing record. At goods-in, review branch stock-location control before releasing the lot. This gives the import distributor a documented basis for consistent rebuild-bench identification when the next order is raised.

28100-1170 Starter Motor Export Supply and Inventory Planning

Elecdura supports qualified wholesale orders from 20 pieces, with normal preparation of 7–15 days after order confirmation and an 18-month warranty under agreed sales terms. Neutral packaging is available, and private-label requirements can be reviewed against order quantity, artwork and delivery schedule.

Demand from a regional transport workshop should keep 28100-1170 tied to Hino EH700/H07C. For engine-overhaul planning, the import distributor can use an engine-rebuild allocation, record the removed-unit dimensions and review branch stock-location control at goods-in. This supports consistent rebuild-bench identification while keeping sample-to-bulk scheduling visible.

The video below introduces Elecdura starter-motor production and electrical testing for B2B supply. Buyers can review factory capability while using the 28100-1170 application and specification shown above for their own product comparison.

28100-1170 Hino EH700/H07C Starter Motor FAQs

How can an import distributor source 28100-1170 for engine-overhaul planning?

Import distributor teams should tie 28100-1170 to Hino EH700/H07C, 24V, 4.5kW, 11T and the removed-unit photographs before requesting price. For engine-overhaul planning, state quantity, destination and delivery timing, then review branch stock-location control. Ask Elecdura to address sample-to-bulk scheduling and consistent rebuild-bench identification in the same quotation.

Sample-to-bulk scheduling question: How can a distributor plan stock for 28100-1170?

Use active Hino EH700/H07C customers or machines, recent usage, replenishment time and the cost of an emergency shortage. Separate trial pieces from normal branch stock and project demand. A defined reorder point is more reliable than buying a mixed group only when one urgent workshop request appears. File 28100-1170 with the branch stock-location control check.

What should be checked before installing the 28100-1170 starter?

Load-test the battery, measure voltage drop on positive and ground circuits, inspect cable lugs and confirm the engine turns freely. Check the ring gear and mounting-ground contact as well. These steps help separate a starter concern from weak batteries, high resistance or mechanical drag that can produce similar symptoms. Keep 28100-1170 traceable through engine-overhaul planning.

For sample-to-bulk scheduling, is a matching 11T pinion enough to approve 28100-1170?

No. Tooth count is only one control. The locating face, mounting pattern, pinion reach, 40mm reference, solenoid position, terminals and 24V system must also agree with the removed starter. Review the full set before a sample or bulk order is accepted. Retain 28100-1170 for consistent rebuild-bench identification and receiving review.

Sample-to-bulk scheduling question: How should branches keep 28100-1170 separate from similar starters?

Use the full reference, Hino EH700/H07C application and core specification on the internal item label. Store the confirmed product photographs with the ERP record and avoid abbreviating the number. Receiving staff can then compare each new lot with the same documented configuration before distributing it to branches. Retain the 28100-1170 result for engine-overhaul planning.

For sample-to-bulk scheduling, what should a buyer include in the 28100-1170 quotation request?

Send the complete 28100-1170 reference, Hino EH700/H07C details, quantity, destination and required date. Add clear front, side and terminal photographs of the removed starter. This gives Elecdura enough information to discuss the intended 24V 4.5kW 11T unit, packing, lead time and freight in one focused offer. File 28100-1170 with the branch stock-location control check.

To support consistent rebuild-bench identification, when is a sample order useful for 28100-1170?

A sample is useful when the old label is incomplete, the application record is uncertain or several similar housings are in local stock. Confirm the sample against mounting, drive and electrical details before scaling the order. Keep the accepted photographs and measurements for later purchasing and receiving checks. This supports consistent rebuild-bench identification for 28100-1170.

Branch stock-location control check: Which physical details matter most when comparing 28100-1170?

Compare 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation with the removed starter, using a straight flange view and a side view parallel to the shaft. Also inspect the locating surface and drive projection. Matching only paint, motor diameter or one mounting ear can hide a difference that affects installation or pinion engagement. Carry the 28100-1170 result into sample-to-bulk scheduling.

Send 28100-1170 Starter Motor RFQ Details to Elecdura

Email info@elecdurauto.com with 28100-1170, Hino EH700/H07C details, old-unit photographs, quantity, delivery country and required date. Elecdura will reply with the matching 24V 4.5kW 11T offer, availability, packing, lead time and freight options.