English
M8T60972
M8T60972
Elecdura
Available for qualified orders
20 pcs
7 - 15 Days
Neutral packaging / private-label review
18 Months
M8T60972
Isuzu 6HK1; 24V, 5.0kW, 11T, 40mm pinion reference
Confirm 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation, 24V, 5.0kW, solenoid position and terminal layout against the removed starter before volume supply.
| Quantity: | |
|---|---|
M8T60972 for Isuzu 6HK1 is presented for wholesale enquiries with the listed 24V, 5.0kW and 11T specification. That precise identity gives commercial buyers a practical starting point for checking fit, availability, packing and delivery without relying on a broad starter-family description.
Regional parts dealer teams handling repeat-lot review should send M8T60972, the Isuzu 6HK1 record, required quantity, destination and delivery timing together. Add straight drive-end and terminal-side photographs of the removed starter. Elecdura can then address shorter machine downtime, repeat-order carton marks and the correct physical configuration in one useful commercial offer.
| Primary order identity | M8T60972 |
| Target application | Isuzu 6HK1 |
| Starter design | Mitsubishi-type replacement |
| System voltage | 24V |
| Rated output | 5.0kW |
| Pinion identification | 11T / 40mm reference |
| OE / reference group | M8T60972 |
| Wholesale terms | MOQ 20 pcs / normally 7–15 days after order confirmation |
| Warranty | 18 months under agreed sales terms |
The key fit controls are 11T pinion and 40mm reference, mounting face, drive reach, solenoid position and terminal orientation. Compare them as one geometry set, then check the locating face and drive projection against the removed starter. This is more reliable than matching one bolt hole or using an angled marketplace photograph.
Electrical identity and mechanical fit must agree. Verify 24V, the 5.0kW rating and terminal layout, then count the 11 pinion teeth. A correct flange with the wrong system voltage, output or cable position is not an acceptable substitute.
Use M8T60972 as the primary searchable order identity. If the label or service record shows an alternate reference, list its complete format and source on a separate RFQ line until voltage, output, drive and mounting have all been compared.
For repeat-lot review, keep M8T60972, Isuzu 6HK1, 24V, 5.0kW and 11T on one purchasing record. At goods-in, review flange and locating-register fit before releasing the lot. This gives the regional parts dealer a documented basis for shorter machine downtime when the next order is raised.
Elecdura supports qualified wholesale orders from 20 pieces, with normal preparation of 7–15 days after order confirmation and an 18-month warranty under agreed sales terms. Neutral packaging is available, and private-label requirements can be reviewed against order quantity, artwork and delivery schedule.
Demand from a diesel rebuild bench should keep M8T60972 tied to Isuzu 6HK1. For repeat-lot review, the regional parts dealer can use a fast-moving counter stock, keep the flange measurement sheet and review flange and locating-register fit at goods-in. This supports shorter machine downtime while keeping repeat-order carton marks visible.
Watch the Elecdura factory video for an overview of starter-motor manufacturing and electrical testing. For purchasing, keep M8T60972, Isuzu 6HK1 and the confirmed physical configuration on the quotation.
Regional parts dealer teams should tie M8T60972 to Isuzu 6HK1, 24V, 5.0kW, 11T and the removed-unit photographs before requesting price. For repeat-lot review, state quantity, destination and delivery timing, then review flange and locating-register fit. Ask Elecdura to address repeat-order carton marks and shorter machine downtime in the same quotation.
A sample is useful when the old label is incomplete, the application record is uncertain or several similar housings are in local stock. Confirm the sample against mounting, drive and electrical details before scaling the order. Keep the accepted photographs and measurements for later purchasing and receiving checks. Use M8T60972 when arranging repeat-order carton marks.
Load-test the battery, measure voltage drop on positive and ground circuits, inspect cable lugs and confirm the engine turns freely. Check the ring gear and mounting-ground contact as well. These steps help separate a starter concern from weak batteries, high resistance or mechanical drag that can produce similar symptoms. File M8T60972 with the flange and locating-register fit check.
Neutral packaging is available, and private-label requirements can be reviewed for qualified orders. Send the expected quantity, artwork, label fields, carton preference and destination early. Elecdura will confirm what can be supported, any additional preparation and the effect on lead time before the order is finalized. File M8T60972 with the flange and locating-register fit check.
Use the full reference, Isuzu 6HK1 application and core specification on the internal item label. Store the confirmed product photographs with the ERP record and avoid abbreviating the number. Receiving staff can then compare each new lot with the same documented configuration before distributing it to branches. Link M8T60972 photographs to the flange and locating-register fit record.
Send the complete M8T60972 reference, Isuzu 6HK1 details, quantity, destination and required date. Add clear front, side and terminal photographs of the removed starter. This gives Elecdura enough information to discuss the intended 24V 5.0kW 11T unit, packing, lead time and freight in one focused offer. Carry the M8T60972 result into repeat-order carton marks.
Use active Isuzu 6HK1 customers or machines, recent usage, replenishment time and the cost of an emergency shortage. Separate trial pieces from normal branch stock and project demand. A defined reorder point is more reliable than buying a mixed group only when one urgent workshop request appears. Keep M8T60972 traceable through repeat-lot review.
The application gives purchasing and receiving teams context that a reference alone may not provide. Keeping Isuzu 6HK1, the electrical rating, pinion and confirmed photographs together makes repeat ordering clearer and reduces the chance that a visually related starter from another machine or engine family is substituted. Link M8T60972 photographs to the flange and locating-register fit record.
Email info@elecdurauto.com with M8T60972, Isuzu 6HK1 details, old-unit photographs, quantity, delivery country and required date. Elecdura will reply with the matching 24V 5.0kW 11T offer, availability, packing, lead time and freight options.
