UD19576S Mitsubishi Starter Motor 12V 2.00kW 13T

UD19576S Mitsubishi Starter Motor Wholesale Supply for Distributors

For distributors and fleet-parts buyers, UD19576S identifies a 12V, 2.00kW, 13-tooth clockwise configuration for Mitsubishi vehicles and equipment cross-referenced to UD19576S. Approve the complete reference, rating, drive end, mounting face, pinion and terminals against the removed unit or signed sample so a nearby version is not substituted into the purchasing line.

The distributor record for UD19576S should connect the reference group UD19576S / 6000608522 / 1810A331 with Mitsubishi vehicles and equipment cross-referenced to UD19576S. Add the old-unit label, mounting-face image, terminal view and receiving result to that record. Reuse it for repeat quotations, but create a new revision whenever the supplier changes the suffix, housing, pinion or electrical rating. A disciplined record reduces avoidable substitutions during urgent replenishment.

UD19576S Starter Motor B2B Production and Test Video for Wholesale Supply

This video introduces Elecdura starter-motor production and supply capabilities. Use the specification, cross-reference details and fitment checks on this page when evaluating UD19576S.

UD19576S Starter Motor Distributor Specifications for Distributor Sourcing

UD19576S Starter Motor OE Cross-Reference Review for Bulk Procurement

Use UD19576S as the primary purchasing reference and cross-check 6000608522, 1810A331. These numbers identify the candidate starter family, but approval still requires the exact suffix, electrical rating, drive end, mounting geometry, pinion and terminal layout to match the removed unit or signed sample.

UD19576S Starter Motor Bulk Fitment Approval for B2B Supply

Confirm the complete UD19576S / 6000608522 / 1810A331 group together with the 12V, 2.00kW, 13-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

UD19576S Starter Motor Wholesale Receiving Inspection for Aftermarket Buyers

For a wholesale shipment, sample units across the UD19576S lot rather than inspecting only the top carton. Compare reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability with the approval record and document pass, fail and hold quantities. Do not mix a disputed suffix or drive-end version with cleared stock, even when the outer housing looks alike.

UD19576S Starter Motor MOQ and Private-Label Supply for Fleet Replacement

UD19576S Starter Motor Distributor FAQ for Wholesale Supply

Which OE numbers should a distributor match for UD19576S?

Use UD19576S as the control reference and compare the complete group UD19576S / 6000608522 / 1810A331. A cross-reference narrows the candidate, but it does not prove that every suffix has the same rating or mounting. Keep the removed-unit label, drive-end photograph, mounting-face view and rear-terminal view in the approval file, then connect that evidence to one quotation and purchase line so repeat orders remain traceable.

Where is UD19576S commonly used, and what still needs confirmation?

Confirm the complete UD19576S / 6000608522 / 1810A331 group together with the 12V, 2.00kW, 13-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

What specification mismatch creates the greatest risk on UD19576S?

Confirm the complete UD19576S / 6000608522 / 1810A331 group together with the 12V, 2.00kW, 13-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

Which configuration checks prevent a mismatched UD19576S order?

Confirm the complete UD19576S / 6000608522 / 1810A331 group together with the 12V, 2.00kW, 13-tooth clockwise configuration. Similar appearance or a shared partial number is not enough; compare equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement against the removed unit or approved sample and keep the signed sample with the purchase record.

Which mounting details should be compared before ordering UD19576S?

Compare the equipment and engine record, complete OE, mounting face, pinion position and terminal arrangement with the removed starter. Check bolt-hole spacing, locating diameter, starter clocking, pinion rest position and rear-terminal clearance instead of judging from the outer housing alone. Never pull a misaligned unit into place with mounting bolts. A measured or photographed fitment record is especially valuable when nearby references share the same voltage and tooth count but use another drive-end or solenoid orientation.

Which incoming-inspection points matter for UD19576S?

Tie every carton and sampled unit to UD19576S, the approved cross-reference set and the supplier lot. Inspect reference label, electrical rating, drive end, mounting geometry, terminals, packing and lot traceability, then measure and compare the sampled unit with the signed photos or dimensional record. Record pass and fail quantities before the stock is mixed. Quarantine any different rating, pinion, mounting face or terminal layout, because an unverified substitute can stop equipment, generate a claim and turn a low unit price into a costly order. This receiving discipline is cheaper than sorting returns after distribution.

Can a similar 12V starter replace UD19576S?

A substitute is acceptable only when its complete OE relationship, 12V system, 2.00kW rating, 13T, rotation and mounting geometry agree with the approved unit. Similar appearance or a shared partial number is not enough. Ask for application and old-unit details, then test or approve a sample before changing the purchase line. Keep materially different versions separate in inventory so warehouse staff cannot fulfil one inquiry with the wrong variant.

How can buyers separate a UD19576S fault from an equipment fault?

Check battery capacity, voltage drop, start signal, grounds, ring gear and mechanical engine load before condemning the starter. Record battery voltage at rest and during the start command, then measure voltage drop under load; a weak supply or poor ground can imitate starter failure. Inspect the mounting surface and gear engagement as well. Attach these results, the old-unit label and failure symptoms to the claim so the supplier can distinguish a product defect from an upstream electrical or mechanical problem.

What makes a UD19576S RFQ technically complete?

Send UD19576S and all visible OE numbers, the full application or engine record, required quantity, destination and target delivery date. Add clear photos of the label, drive end, mounting face and terminals, plus any dimensional drawing available. State packaging, private-label, sample and inspection requirements at the start. A technically complete RFQ lets the supplier quote one verified configuration and reduces clarification delays after price approval.

Request a B2B Quote for UD19576S Starter Motors

Send the complete reference, Mitsubishi vehicles and equipment cross-referenced to UD19576S, old-unit photos, quantity, destination and packaging or inspection requirements. Elecdura will use that evidence to review one defined aftermarket starter configuration for your quotation.